NXP公司的UBA2016A/15/15是集成了PFC,線性調光和升壓功能的600V熒光燈驅動器,包括熒光燈驅動模塊,半橋驅動器,臨界導通模式的PFC控制器/驅動器以及幾種保護功能,主要用于通用照明的小型熒光燈和管燈驅動.本文介紹了UBA2016A/15/15A主要特性和優勢與方框圖, 基本的PFC應用電路圖, 燈電流控制圖和多種應用電路圖,以及UBA2015AP 120 V (AC) 評估板指標,電路圖,材料清單和PCB元件布局圖.

UBA2016A/15/15A:600 V fluorescent lamp driver with PFC, linear dimming and boost function

The UBA2016A/15/15A are high voltage Integrated Circuits (IC) intended to drive fluorescent lamps with filaments such as Tube Lamps (TL) and Compact Fluorescent Lamps (CFL) in general lighting applications. The IC comprises a fluorescent lamp control module, half-bridge driver, built-in critical conduction mode Power Factor Correction(PFC) controller/driver and several protection mechanisms. The IC drives fluorescent lamp(s) using a half-bridge circuit made of two MOSFETs with a supply voltage of up to 600 V.

The UBA2016A/15/15A are designed to be supplied by a start-up bleeder resistor and a dV/dt supply from the half-bridge circuit, or any other auxiliary supply derived from the half-bridge or the PFC. The supply current of the IC is low. An internal clamp limits the supply voltage.

UBA2016A/15/15A主要特性和優勢:

? Power factor correction features:

? Integrated 4-pin critical conduction mode PFC controller/driver

? Open and short pin-short protection on PFC feedback pin

? Overcurrent protection

? Overvoltage protection

? Half-bridge driver features:

? Integrated level-shifter for the high-side driver of the half-bridge

? Integrated bootstrap diode for the high-side driver supply of the half-bridge

? Independent non-overlap time

? Fluorescent lamp controller features:

? Linear dimming (UBA2016A and UBA2015A only)

? EOL (End-Of-Life) detection (both symmetrical and asymmetrical)

? Adjustable preheat time

? Adjustable preheat current

? Adjustable fixed frequency preheat (UBA2015 and UBA2015A only)

? Lamp ignition failure detection

? Ignition detection of all lamps at multiple lamps with separate resonant tanks

? Second ignition attempt if first failed

? Constant output power independent of mains voltage variations

? Automatic restart after changing lamps

? Adjustable lamp current boost at start-up (UBA2016A only)

? Lamp current control

? Enable input (UBA2015 and UBA2015A only)

? Protection

? Hard switching/capacitive mode protection

? Half-bridge overcurrent (coil saturation) protection

? Lamp overvoltage (lamp r

UBA2016A/15/15A 應用:

Intended for fluorescent lamp ballasts with either a dimmable (UBA2016A and UBA2015A) or a fixed (UBA2015) output and PFC for AC mains voltages of up to 390 V.

圖1.UBA2016A方框圖

圖2.UBA2015A和UBA2015方框圖

圖3. UBA2016A/15/15A基本的PFC應用電路圖

圖4. UBA2016A/15/15A基本的半橋和IC電源連接電路圖

圖5. 燈電流控制圖

圖6. UBA2016A升壓應用案例圖
Vo(PFC) = 430 V的元件值:
Rhv = 22Mohm(500 V); Chv = 100 nF (500 V); Dreset = 1N4148; CBOOST = 150 nF (63 V);
RBOOST = 10 Mohm and Rbias = 10 Mohm

圖7. UBA2016A TL或CFL應用電路圖(火線濾波器未顯示)

圖8. UBA2016A基本的TL或CFL應用電路圖(有較好的PFC性能)(火線濾波器未顯示)

圖9. UBA2016A 固定時間升壓起動的TL或CFL應用電路圖(火線濾波器未顯示)

圖10. UBA2016A 取決于燈溫度的升壓起動的TL或CFL應用電路圖(火線濾波器未顯示)

圖11. UBA2016A 可調光TL應用電路圖(火線濾波器未顯示)

UBA2015AP 120 V (AC) 評估板

This evaluation board is intended to build applications with the UBA2016A, UBA2015A and UBA2015 ballast controller family. This document describes the specification and use of the board. Default, this ballast design is intended to drive one TL5HE35W lamp with the UBA2015AP. However, several options are provided on the board to use it with the UBA2016AP and UBA2015P.

圖12.UBA2015AP 120 V (AC) 評估板外形圖
UBA2015AP 120 V (AC) 評估板指標:

支持的燈類型:


圖13.UBA2015AP 120 V (AC) 評估板連接圖

圖14.UBA2015AP 120 V (AC) 評估板方框圖

圖15.UBA2015AP 120 V (AC)評估板電路圖:半橋電路

圖16.UBA2015AP 120 V (AC)評估板電路圖:PFC電路

圖17.UBA2015AP 120 V (AC)評估板電路圖:控制電路

圖18.UBA2015AP 120 V (AC)評估板電路圖:調光輸入電路

圖19.UBA2015AP 120 V (AC)評估板電路圖:測試點電路

UBA2015AP 120 V (AC)評估板材料清單(BOM):






圖20.UBA2015AP 120 V (AC)評估板元件布局圖(頂層)

圖21.UBA2015AP 120 V (AC)評估板元件布局圖(底層)
詳情請見:
http://www.nxp.com/documents/data_sheet/UBA2016A_15_15A.pdf
和
http://www.nxp.com/documents/user_manual/UM10438.pdf