</a>LED" title="LED">LED" title="LED">LED驅動器采用LinkSwitchTM-PH LNK417EG器件和±3% CC調整,具有高效率,功率因素大于0.9,AC輸入電壓90V-265V,滿足IEC 61000-4-5環形波, IEC 61000-3-2 Class C諧波和EN55015 B接觸EMI要求,起動時間小于100ms.本文介紹了該驅動器主要特性和指標, 驅動器和子板電路圖以及相應的材料清單與PCB布局圖.
This document describes an isolated, power factor corrected, very high efficiency LED driver (non-dimmable) designed to drive an LED string of 30 V at a current of 500 mA(both nominal) from an input voltage range of 90 VAC to 265 VAC. The design employs a secondary side current feedback circuit to achieve less than 3% output current regulation over line and load. A reference board DER-284 was used with the secondary constant current regulation daughter board added to demonstrate how this technique can be used on and LinkSwitch-PH flyback design.
The LED driver uses a LNK417EG device from the LinkSwitch-PH family of ICs. This integrated controller and 725 V MOSFET dramatically reduces complexity and omponent count.
This document contains the LED driver specification, schematic, and bill of material,transformer documentation and typical performance characteristics.
15W LED驅動器主要特性:
≤3% output current regulation over line and load
Highly energy efficient
Efficiency ≥88% at 115 VAC and 230 VAC input
Low cost, low component count and small printed circuit board footprint solution
Frequency jitter for smaller, lower cost EMI filter components
Integrated protection and reliability features
Output open-circuit / output short-circuit protection with auto-recovery
Line input overvoltage shutdown extends voltage withstand during line faults.
Auto-recovering thermal shutdown with large hysteresis protects both components
and printed circuit board
No damage during brown-in or brown-out conditions
Meets IEC 61000-4-5 ring wave, IEC 61000-3-2 Class C harmonics and EN55015 B conducted EMI
Clean start-up – no output blinking
Fast start-up (<100 ms) – no perceptible delay
圖1.15W LED驅動器外形圖
15W LED驅動器指標:
圖2.15W LED驅動器電路圖
圖3.15W LED驅動器子板電路圖
圖4.15W LED驅動器PCB布局圖
圖5.子板PCB布局圖
15W LED驅動器材料清單:
子板材料清單:
圖6.變壓器電路圖
詳情請見:
http://www.powerint.com/sites/default/files/PDFFiles/der289.pdf
This document describes an isolated, power factor corrected, very high efficiency LED driver (non-dimmable) designed to drive an LED string of 30 V at a current of 500 mA(both nominal) from an input voltage range of 90 VAC to 265 VAC. The design employs a secondary side current feedback circuit to achieve less than 3% output current regulation over line and load. A reference board DER-284 was used with the secondary constant current regulation daughter board added to demonstrate how this technique can be used on and LinkSwitch-PH flyback design.
The LED driver uses a LNK417EG device from the LinkSwitch-PH family of ICs. This integrated controller and 725 V MOSFET dramatically reduces complexity and omponent count.
This document contains the LED driver specification, schematic, and bill of material,transformer documentation and typical performance characteristics.
15W LED驅動器主要特性:
≤3% output current regulation over line and load
Highly energy efficient
Efficiency ≥88% at 115 VAC and 230 VAC input
Low cost, low component count and small printed circuit board footprint solution
Frequency jitter for smaller, lower cost EMI filter components
Integrated protection and reliability features
Output open-circuit / output short-circuit protection with auto-recovery
Line input overvoltage shutdown extends voltage withstand during line faults.
Auto-recovering thermal shutdown with large hysteresis protects both components
and printed circuit board
No damage during brown-in or brown-out conditions
Meets IEC 61000-4-5 ring wave, IEC 61000-3-2 Class C harmonics and EN55015 B conducted EMI
Clean start-up – no output blinking
Fast start-up (<100 ms) – no perceptible delay
圖1.15W LED驅動器外形圖
15W LED驅動器指標:
圖2.15W LED驅動器電路圖
圖3.15W LED驅動器子板電路圖
圖4.15W LED驅動器PCB布局圖
圖5.子板PCB布局圖
15W LED驅動器材料清單:
子板材料清單:
圖6.變壓器電路圖
詳情請見:
http://www.powerint.com/sites/default/files/PDFFiles/der289.pdf
本站內容除特別聲明的原創文章之外，轉載內容只為傳遞更多信息，并不代表本網站贊同其觀點。轉載的所有的文章、圖片、音/視頻文件等資料的版權歸版權所有權人所有。本站采用的非本站原創文章及圖片等內容無法一一聯系確認版權者。如涉及作品內容、版權和其它問題，請及時通過電子郵件或電話通知我們，以便迅速采取適當措施，避免給雙方造成不必要的經濟損失。聯系電話：010-82306118；郵箱：aet@chinaaet.com。