NXP公司的LPC1857/53是基于ARM Cortex-M3內的 32位MCU，具有高達1MB閃存，136kB SRAM，以太網和兩個高速USB以及LCD和EMC等。ARM Cortex-M3處理器工作頻率高達180MHz，內置了支持8個區域的存儲器保護單元（MPU）和嵌套向量中斷控制器 (NVIC)，具有豐富外設，主要用在工業控制，RFID閱讀器，電子測量儀器，消費類電子和白色家電。本文介紹了LPC1857/53主要特性和優勢，方框圖，以及Hitex LPC1850評估板主要特性，電路圖和元件布局圖。

The LPC1857/53 are ARM Cortex-M3 based microcontrollers for embedded applications.

The ARM Cortex-M3 is a next generation core that offers system enhancements such as low power consumption, enhanced debug features, and a high level of support block integration.

The LPC1857/53 operate at CPU frequencies of up to 180 MHz. The ARM Cortex-M3 CPU incorporates a 3-stage pipeline and uses a Harvard architecture with separate local instruction and data buses as well as a third bus for peripherals. The ARM Cortex-M3 CPU also includes an internal prefetch unit that supports speculative branching.

The LPC1857/53 include up to 1 MB of flash and 136 kB of on-chip SRAM, 16 kB of EEPROM memory, a quad SPI Flash Interface (SPIFI), a State Configurable Timer (SCT)subsystem, two High-speed USB controllers, Ethernet, LCD, an external memory controller, and multiple digital and analog peripherals.

LPC1857/53主要特性和優勢：

? Processor core

? ARM Cortex-M3 processor, running at CPU frequencies of up to 180 MHz.

? ARM Cortex-M3 built-in Memory Protection Unit (MPU) supporting eight regions.

? ARM Cortex-M3 built-in Nested Vectored Interrupt Controller (NVIC).

? Non-maskable Interrupt (NMI) input.

? JTAG and Serial Wire Debug, serial trace, eight breakpoints, and four watch points.

? Enhanced Trace Module (ETM) and Enhanced Trace Buffer (ETB) support.

? System tick timer.

? On-chip memory

? Up to 1 MB on-chip dual bank flash memory with flash accelerator.

? 16 kB on-chip EEPROM data memory.

? 136 kB SRAM for code and data use.

? Multiple SRAM blocks with separate bus access.

? 64 kB ROM containing boot code and on-chip software drivers.

? 32-bit One-Time Programmable (OTP) memory for general-purpose use.

? Clock generation unit

? Crystal oscillator with an operating range of 1 MHz to 25 MHz.

? 12 MHz internal RC oscillator trimmed to 1 % accuracy over temperature and voltage.

? Ultra-low power RTC crystal oscillator.

? Three PLLs allow CPU operation up to the maximum CPU rate without the need for a high-frequency crystal. The second PLL is dedicated to the High-speed USB, the third PLL can be used as audio PLL.

? Clock output.

? Configurable digital peripherals:

? State Configurable Timer (SCT) subsystem on AHB.

? Global Input Multiplexer Array (GIMA) allows to cross-connect multiple inputs and outputs to event driven peripherals like timers, SCT, and ADC0/1.

? Serial interfaces:

? Quad SPI Flash Interface (SPIFI) with 1-, 2-, or 4-bit data at rates of up to 40 MB per second.

? 10/100T Ethernet MAC with RMII and MII interfaces and DMA support for high throughput at low CPU load. Support for IEEE 1588 time stamping/advanced time stamping (IEEE 1588-2008 v2).

? One High-speed USB 2.0 Host/Device/OTG interface with DMA support and on-chip high-speed PHY (USB0).

? One High-speed USB 2.0 Host/Device interface with DMA support, on-chip full-speed PHY and ULPI interface to external high-speed PHY (USB1).

? USB interface electrical test software included in ROM USB stack.

? Four 550 UARTs with DMA support: one UART with full modem interface; one UART with IrDA interface; three USARTs support UART synchronous mode and a smart card interface conforming to ISO7816 specification.

? Two C_CAN 2.0B controllers with one channel each.

? Two SSP controllers with FIFO and multi-protocol support. Both SSPs with DMA support.

? One Fast-mode Plus I2C-bus interface with monitor mode and with open-drain I/O pins conforming to the full I2C-bus specification. Supports data rates of up to 1 Mbit/s.

? One standard I2C-bus interface with monitor mode and standard I/O pins.

? Two I2S interfaces with DMA support, each with one input and one output.

? Digital peripherals:

? External Memory Controller (EMC) supporting external SRAM, ROM, NOR flash, and SDRAM devices.

? LCD controller with DMA support and a programmable display resolution of up to 1024H ? 768V. Supports monochrome and color STN panels and TFT color panels; supports 1/2/4/8 bpp Color Look-Up Table (CLUT) and 16/24-bit direct pixel mapping.

? SD/MMC card interface.

? Eight-channel General-Purpose DMA (GPDMA) controller can access all memories on the AHB and all DMA-capable AHB slaves.

? Up to 164 General-Purpose Input/Output (GPIO) pins with configurable pull-up/pull-down resistors and open-drain modes.

? GPIO registers are located on the AHB for fast access. GPIO ports have DMA support.

? Up to 8 GPIO pins can be selected from all GPIO pins as edge and level sensitive interrupt sources.
? Two GPIO group interrupt modules enable an interrupt based on a programmable pattern of input states of a group of GPIO pins.

? Four general-purpose timer/counters with capture and match capabilities.

? One motor control PWM for three-phase motor control.

? One Quadrature Encoder Interface (QEI).

? Repetitive Interrupt timer (RI timer).

? Windowed watchdog timer.

? Ultra-low power Real-Time Clock (RTC) on separate power domain with 256 bytes of battery powered backup registers.

? Event recorder with three inputs to record event identification and event time; can be battery powered.

? Alarm timer; can be battery powered.

? Analog peripherals:

? One 10-bit DAC with DMA support and a data conversion rate of 400 kSamples/s.

? Two 10-bit ADCs with DMA support and a data conversion rate of 400 kSamples/s. Decryption:

? Hardware-based AES decryption programmable through an on-chip API.

? Two 128-bit secure OTP memories for AES key storage and customer use.

? Random Number Generator (RNG) accessible through AES API.

? Unique ID for each device.

? Power:

? Single 3.3 V (2.2 V to 3.6 V) power supply with on-chip internal voltage regulator for the core supply and the RTC power domain.

? RTC power domain can be powered separately by a 3 V battery supply.

? Four reduced power modes: Sleep, Deep-sleep, Power-down, and Deep power-down.

? Processor wake-up from Sleep mode via wake-up interrupts from various peripherals.

? Wake-up from Deep-sleep, Power-down, and Deep power-down modes via external interrupts and interrupts generated by battery powered blocks in the RTC power domain.

? Brownout detect with four separate thresholds for interrupt and forced reset.

? Power-On Reset (POR).

? Available as LQFP208, LBGA256, or TFBGA180 packages.

LPC1857/53應用：

? Industrial

? RFID readers

? Consumer

? e-Metering

? White goods

圖1。LPC1857/53方框圖

Hitex LPC1850評估板

The Hitex LPC1850 Eval board allows you to quickly and easily evaluate the LPC1800 family of microcontrollers. The microcontroller, board, and the accompanying features make it a great starting point for your next Cortex-M3 project.

Populated with the LPC1850 to demonstrate LPC1800 features, the LPC1850 offers industry leading performance, large internal memories and advanced peripherals.

Hitex LPC1850評估板主要特性：

The evaluation board has the following features:

- CPU: LPC1850 (ARM Cortex-M3)

- Power-over-Ethernet

- Ready for energy consumption analysis with PowerScale of the complete board, the CPU-core and other peripherals

- SDRAM, SRAM, parallel flash, NAND flash, qSPI flash

- Temperature sensor, SD card, media-connector

- CAN, UART, Ethernet, USB (Host, Device, OTG)

- Debug with standard ARM JTAG and JTAG + Trace connector

- Ready for Jennic ZigBee module

- Small onboard display and NXP standard display / LCD interface

- Touch buttons and LEDs

- Wrap field for user circuits

- Audio IN and OUT, microphone IN, headphones OUT and a D-Class amplifier

- Ready for 4x ADC1415 analog-to-digital converters with user filtering option

圖2。Hitex LPC1850評估板外形圖

圖3。Hitex LPC1850評估板電路圖（1）

圖4。Hitex LPC1850評估板電路圖（2）

圖5。Hitex LPC1850評估板電路圖（3）

圖6。Hitex LPC1850評估板電路圖（4）

圖7。Hitex LPC1850評估板電路圖（5）

圖8。Hitex LPC1850評估板電路圖（6）

圖9。Hitex LPC1850評估板電路圖（7）

圖10。Hitex LPC1850評估板電路圖（8）

圖11。Hitex LPC1850評估板PCB元件布局圖
詳情請見：
http://www.nxp.com/documents/data_sheet/LPC1857_53.pdf
和
http://www.nxp.com/documents/other/Hitex_LPC1850_Eval_Board_Schematics.pdf